全国服务热线:

15853163650
您当前的位置:首页 > 新闻动态 > 公司动态
    联系我们

    CONTACTS US

    地址:山东济南历城区华龙路嘉恒大厦A座1201室

    邮箱:hhjc168@126.com

    公司传真: 0531-88518398

    电话:15853163650

公司动态

COMPANY NEWS

电梯套门窗套安装步骤及参数

2016-05-30 14:10:02 文章来源:www.jnhaohui.com

1、施工流程 :检查安装墙面、套口——定位与放线——检查石塑线条和搭配侧板——结构胶涂点——安装固定——清洁饰面
1, the construction process: check the installation wall, set mouth, positioning and Ray - stone check plastic lines and side plate structure glue Tu point collocation, fixed installation, clean finish
2、检查安装墙面、套口:检查墙面和套口的安装前提是否具备,检查门套预留洞口尺寸是否符合设计要求,窗套检查预留台面是否符合尺寸。
2, check the mounting surfaces, set mouth: check the wall and the mouth of the installation premises have and check door reserved hole size is consistent with the design requirements, Chuangtao check reservation table are in accordance with the dimensions.
3、定位放线:根据设计要求,在实际位置做出基础线,并保证整体方正。门套定位,压框宽度应保证余量尺寸一致。
3, positioning line: according to the design requirements, in the actual position to make the basic line, and to ensure that the overall founder. Door positioning, pressing frame should ensure the uniform size of margin width.
4、检验石塑线条和侧板:安装前,检查石塑线条和侧板的尺寸、规格、加工质量、特备零件的规格以及数量必须符合设计及规范要求。

电梯门套
4, test stone plastic lines and side plate: before installation, check stone plastic lines and side plate dimensions, specifications, processing quality, special parts of the specifications and quantity must comply with the design requirements and specifications.
5、结构胶涂点:在电梯套和门窗套所需的石塑线条和侧板背部进行结构胶均匀打点,间距为10-20CM为宜。
5, the structure of glue Tu point: required in the elevator and sets of doors and windows of stone plastic lines and side plate back structure glue evenly RBI, spacing 10-20CM is appropriate.
6、安装固定:电梯套和门套安装需对安装部位首先量尺,处理接头及转角位置;设计无特殊要求,接头应成45°角;然后直接按照施工图要求进行上墙安装。
6, fixed installation: set of elevator and door installation required on the installation location, scale, joints and corner position processing; design has no special requirements, the joints should be into a 45 degree angle, then directly in accordance with the construction requirements for wall mounting.
7、清洁饰面:安装完工之后撕去饰面的保护膜,用抹布和肥皂水对勾缝出进行清洁处理。
7, clean finish: protective film installation after completion of tear finishes, pointing out to clean with a rag and soapy water.
本文由电梯门套提供帮助,更多的相关内容请点击:http://www.jnhaohui.com我们将详情为您解答.欢迎您的光临!
The elevator door to provide help, more relevant content please click: http://www.jnhaohui.com us the details for you to answer. Welcome your presence!