电梯门套施工方案
The elevator door construction scheme
1、将厅门处门洞进行处理。厅门处一般是安装石材覆盖在表面。石材在安装前要进行表面处理，保持清洁和干燥度，含水率要小于8%。
1, the hall door at the door handle. Hall door is generally installed stone covered in the surface. The stone shall be treated with surface treatment before installation. It shall be clean and dry, with a moisture content of less than 8%.
2、用安装门套的石材应该保持花纹、颜色的一致性。所以要进行仔细甄选，避免出现严重的色差和花纹差异性。每一层的所有电梯门套石材都要保持统一性。

2, with the installation of door should maintain consistency of stone pattern, color. Therefore, careful selection should be carried out to avoid severe color difference and pattern difference. All the elevator door stone of each layer to maintain unity.
3、正式安装石材之间，再将石材做一次彻底清理，结构部分不能留有渣质，表面无积灰污垢。然后用墨线弹出水平线和垂直线。
3, the formal installation of stone between, and then make a thorough cleaning of stone, the structural part of the slag can not be retained, the surface without ash fouling. Then use the pop-up Moxian horizontal and vertical lines.
4、根据弹出的线条位置，使用钻机在需要打孔处打孔。孔眼的直径一般是8mm左右，深度是12mm左右。按照施工标准，每块石板上、下面都要打孔眼，位于石板中间位置。
4, according to the pop-up line position, use drilling machine in need punch hole drill. The diameter of the hole is about 8mm, and the depth is about 12mm. According to the construction standard, every stone slab should be lined with holes, located in the middle of the stone slab.
5、将膨胀螺栓固定在墙面上，然后将角架固定好，再将挂件安装在角架上。
5. Fix the expansion bolt on the wall surface, then fix the angle frame, and then install the pendant on the corner frame.
6、角架和挂件安装好之后，进行石材开槽工序。将石材固定在挂件上时使用专用的大理石胶，黏结好之后反复压几次，确定不会脱落。
6, after the angle and the pendant installation, carries on the stone slotting process. When the stone is fixed on the pendant, use the special marble glue, and then press it several times to make sure it won't fall off.
7、安装好之后的电梯门套应该做到光面平整，立面垂直，接缝平直，接缝宽度的偏差不能超过2mm。
The elevator door 7, installed should be smooth flat, vertical, straight seam, seam width deviation of not more than 2mm.
8、电梯门套全部安装完之后，将表面石材做一次清理工作，即可投入使用。
After 8, all installed the elevator door, a cleaning surface stone, can be put into use.
电梯门套施工注意事项
The elevator door construction matters needing attention
1、在安装电梯门套时，想要将各层需要的石材挑选好。根据尺寸、颜色和花纹来搭配，然后搬运到各个楼层需要使用的地方。
1, installed in the elevator door, to each layer of stone selection. Match by size, color, and pattern, and then move to where each floor needs to be used.
2、在安装时要注意石材的纹理，尽量保持色泽一致，纹理连贯。安装完成之后，电梯门套的美观性才会最佳。
2, in the installation should pay attention to stone texture, as far as possible to maintain color consistency, texture coherence. After the installation is complete, the appearance of the elevator door will be the best.
3、弹线的时候要仔细测量，不仅一个门套要做好垂直和平整性，每个门套之间也要注意这些问题。
When I was 3, playing the line must be measured carefully, not only a door to do vertical integration of peace, we should pay attention to these problems between each.
4、安装角钢的位置要测量精确，在中间增加一个加固点的点位。这样做是为了让门套石材更加稳定、牢固。
4. The position of the angle iron shall be measured accurately, and a point of reinforcement shall be added in the middle. This is done in order to make more stable and solid stone door.
以上的介绍，您了解了吗?如果您有不明白的地方，欢迎您的致电，我们全面为您介绍，欢迎您的莅临参观哦。
Have you got the above information? If you don't understand it, you are welcome to call us. We would like to introduce you to all of you.