1、首先在选购时要注意生产企业的厂名、厂址、商标是否齐全。
1, we should pay attention to when choosing the name and address of the manufacturer, the trademark production enterprises are complete.
因为只有标识齐全的板材才能得到应有的质量保证。
Because only the plate can get the proper quality assurance.
2、表面无明显瑕疵。
2, surface no obvious defects.
板材表面应光洁、无毛刺沟痕和刨刀痕，无透胶现象，板面无局部发黄、发黑等污染现象。
Plate surface should be smooth, without burr grooves and planer marks and without penetrating the phenomenon of rubber, the surface without local yellow, black and other pollution phenomenon.
3、区分人造和天然贴面。
3, distinguish between artificial and natural veneer.
通常人造薄木单板贴面的纹理基本为通直纹理，纹理图案有规则; 而天然木质单版贴面为天然木质花纹，纹理图案自然而无规则，变异性比较大。

Usually artificial veneer veneer texture is straight grain, texture pattern rules; and natural wood single plate veneer natural wood patterns, texture pattern naturally without any rules, variability is relatively large.

4、无开胶现象。
4, no glue phenomenon.
胶和强度充分反映了板材胶合性能的优劣，胶合强度值约高，胶合性能就越好。 在选择板材时，应注意装饰板胶层结构稳定、无开胶现象。仔细观察，在表面单版与基材之间、基材内部各层之间不能出现鼓包、分层现象。
Fully reflects the strength and adhesive bonding performance of sheet metal quality, higher bonding strength value, the better the performance bond. In the choice of plate, should pay attention to decorative plate layer structure is stable, without glue phenomenon. Careful observation, in the surface between the single version and the substrate, the substrate between the layers can not occur between the drum package, layered phenomenon.
5、气味应清淡。
5, the smell should be light.
装饰板使用的胶粘剂以脲醛树脂为主，装饰板材经加工处理后，材质中会遗留有少量甲醛，并逐渐释放。这种气味对人体极为有害。 在选购时，可从气味来判断，因为气味越大，说明甲醛释放量越高，污染越厉害，其危害性就越大。
Decorative plate using the adhesive to urea formaldehyde resin based, decorative plate after processing, the material will be left with a small amount of formaldehyde, and gradually released. This smell is very harmful to the human body. In the purchase, you can judge from the smell, because the greater the smell, the higher the formaldehyde emissions, the more serious pollution, the greater the risk.
6、注意含水率。
6, pay attention to moisture content.
通常装饰单版贴面胶合板要求有一定的含水率，其含水率越接近使用地区的平衡含水率越好。 含水率过高或过低，装饰板都会在环境温度变化影响下出现较大的变形。因此，在温度比较小的地区，适宜使用含水率较低的装饰板;反之，则应使用含水率较高的装饰板。
Veneer plywood is usually decorated with a certain percentage of moisture content, the water content of the more close to the use of the region's water balance, the better. The water content is too high or too low, the decorative board will be under the influence of environmental temperature changes appear larger deformation. Therefore, the temperature is relatively small, suitable for the use of lower water content of the decorative plate; otherwise, should use a higher water content of the decorative board.
7、观察纹理结构。
7, observe the texture structure.
在其他项都满意的情况下，还要注意材质应细致均匀、色泽清晰、木纹美观。配板与拼花的纹理应按一定规律排列，且木色相近，无明显色差，拼缝与板边近乎平行。这样的板材才能收到很好的装饰效果。
The other items are satisfied with the situation, but also pay attention to material should be uniform, clear and beautiful wood color. With the plate and mosaic texture should be regular, and the wood color similar, no obvious color difference, and nearly parallel plate edge seam. Such plates can receive a good decorative effect.