石塑电梯套线条是一种pvc+天然石粉组成的新型混合原料，这种原料的电梯套不光具有大理石的斑纹与质地，更具有杰出的耐性与硬度，可以说是一种性价比极高的原料门套资料。那么，石塑电梯套线条的施工流程是什么呢？

The stone plastic elevator sleeve is a new mixture of pvc+ natural stone powder. The elevator sleeve of this kind of raw material can not only have the markings and texture of marble, but also has excellent resistance and hardness. It can be said to be a kind of material with high cost performance. Then, what is the construction process of stone plastic elevator?
1、物料准备：线条、侧板、泡棉胶、硅酮胶（或云石胶）、45°切开锯、台锯、胶枪、红外线仪器；

1, material preparation: lines, side panels, foam glue, silicone rubber (or marble glue), 45 degree cut saw, table saw, glue gun, infrared instrument;
2、布局墙体基面清算清洁外面没有油污、浮尘、并查验墙面平整度和笔直度。超差部分应剔凿或用水泥沙浆修补缺陷，加固找平，方能施工；

2. Lay out the base of the wall and clean it up. There is no oil pollution, floating dust, and check the evenness and straightness of the wall. The oversize part should be chipped or repaired with cement mortar to strengthen the leveling before construction.
3、在墙面找出水平线、笔直控制线；

3. Find out the horizontal line and the straight control line on the wall.
4、切开锯采纳45度角对线条切开并对角拼接反省平整度厚板+线条方式：假设墙面是干挂大理石根基，需要用小木方在墙面上找3-4个点，然后用云石胶点粘，小木方周围用发泡胶加添；然后将切好45度切角的线条卡扣在侧板上，线条另一侧点粘到墙面上；薄板+线条方式：

假设墙面是干挂大理石根基，需要用细木工板打底，然后将薄板用泡棉胶暂时结实，云石胶点粘到细木工板上；然后将薄板切开部分卡在线条卡槽中 ，将线条设备到位，压实，结实在墙体细木工板基面上。卡槽一方面可以遮挡住侧板切开处的瑕疵，另一方面设备速率可以前进。(分外阐明:泡棉胶起到暂时结实的感染，硅酮胶24小时内无法凝结，但其前期感染力强，所以二者一起使用才干到达预期结果)

4, cut saw adopted 45 degrees angle to cut lines and diagonal splicing to reflect the smoothness of thick plate + lines: assuming that the wall is dry and hanging marble foundation, need to use small wood to find 3-4 points on the wall, then use the sticky sticky point of the mica glue, the small wood side with foam glue added around, and then cut the line of 45 degree angle cut on the side board. The other side of the line adheres to the wall.
Assuming that the wall is a dry marble foundation, it needs to be bottled up with a carpenter's board, then the sheet is temporarily sturdy with foam rubber, and the mica glue points to the carpenter board; then the thin plate section is stuck in the line card slot, and the line equipment is in place, compacted and sturdy on the wall carpenter's base surface. On the one hand, the card slot can block the defects on the side board, and on the other hand, the equipment speed can move forward. (expound: foam rubber has a temporary and sturdy infection, and silicone rubber can not condense within 24 hours, but its early infection is strong, so the two use the talent to reach the expected results).
7、将对角处裂缝打硅酮胶填满抹

7. Fill the corner crack with silicone rubber
8、将线条与墙的空隙打胶抹

8. Glue the gap between the line and the wall
9、侧板根据现实尺度用台锯切开，施工办法请参照线条(根基平整，泡棉胶暂时结实，硅酮胶点粘

9. Side panels should be cut by table saws according to the actual scale. The construction methods refer to the lines (the foundation is smooth, the foam glue is temporarily strong, and the silicone glue is sticky.
10、全体竣工

10. Completion of the whole