全国服务热线:

15853163650
您当前的位置:首页 > 新闻动态 > 公司动态
    联系我们

    CONTACTS US

    济南皓晖建材有限公司,总部位于中国泉城——山东济南,是一家专业生产销售石塑电梯门套,仿大理石电梯门套的专业厂家。皓晖建材在电梯门套生产行业很多年,凭着优质的产品质量和完善的售后服务,在全国各地都有我们的工程案例。

    我们本着“以质量求生存 ,靠管理出效益,凭信誉赢口碑,以实干筑辉煌”的经营理念,公司将立足于当代建材现代化发展前沿,依靠科技、勇于探索,以优质产品优良服务、信誉与广大用户携手共创辉煌。

    联系电话: 15853163650

    工厂地址:山东济南章丘区(欢迎广大客户来厂勘察)

公司动态

COMPANY NEWS

仿大理石铺设墙面的步骤

2016-03-17 09:53:19 文章来源:www.jnhaohui.com

一、测量墙面
A measurement of the wall仿大理石线条
测量墙面长宽度,根据仿大理石尺寸,计算出所需仿大理石的整数块,多余空间用仿大理石拼板完成,拼板应分配在端部为宜。
Measurement of wall length and width, according to the size of imitation marble, calculate the integer blocks required for imitation marble, imitation marble panels with extra space, plate should be allocated at the end.
二、踢脚线安装
Two, skirting line installation
处理好墙面,在踢脚线背面打上结构胶,然后按照良好的尺寸,将踢脚线安装到墙面上,湿度高的地区,两根踢脚线结合须留出适当的伸缩缝,特别在放家具的墙角,伸缩缝应考虑多一些。

Treatment of the wall, on the back of the skirting line structure glue, then in accordance with the size of the good, the skirting line is installed onto the wall, high humidity area, two skirting line combination shall be set aside an appropriate amount of expansion joints, especially in put furniture in the corner, expansion joint should be considered more.

仿大理石线条

三、仿大理石安装
Three, imitation marble installation
将仿大理石从左到右插入踢脚线内,起始块应从墙角开凹槽向墙角。遇到柱子时可用阳角。在腰线凹槽内涂上专用胶,数分钟后插到凹凸面,在墙角处必须45°对角。
Insert the imitation marble baseboard from left to right, from the starting blocks to the corner corner open groove. When available corner columns. In the waist groove coated with a special glue, a few minutes after inserted into the concave convex surface, in the corner of the wall must be 45 degrees diagonal.
四、全高型仿大理石安装
Four, the high imitation marble installation
将仿大理石背面涂上结构胶,按照尺寸安装上墙,并用尺子校正,板材下面放到踢脚线里面。
The imitation marble side apply structural adhesive, in accordance with the size of installation on the wall, and with a ruler correction, under the sheet into the inside of the skirting board.
五、顶角线的安装
Five, dingjiaoxian installation
顶角线可以通过两侧涂上专用胶,粘到顶角处,再拉开数分钟,然后再紧紧粘上。
Dingjuexian by both sides coated with a special glue, stick to the vertex, and then opened a few minutes, and then stick on.