电梯门套无接缝翻新是现在建材行业一种新型技术，这种技术相对要节省时间，而且相对成本较低，下面济南皓晖建材的小编就给大家讲解一下：
Elevator door without joint renovation is now building materials industry a new technology, the technology relative to save time, and relatively low cost, the following Jinan Hao Hui building materials Xiaobian is for everyone to explain:
1、先将电梯门套缝隙间原有填充物清理干净，然后使用专用的电梯门套开缝机对原来电梯门套安装的中缝重新整齐切割开缝，使石材间的缝隙的宽度差降至最低，再用接近电梯门套颜色的石胶对其进行填补。
1, first elevator door gap between the original filler to clean up, and then use special elevator door slot machine of original elevator door installation of raphe to neat cutting slot, so that the width of the gap between the stone to minimize the error, and then close the elevator door color of stone glue to fill.
2、使用接近电梯门套本身颜色的石胶并将石胶进行完美的调色，使之充分接近原来电梯门套的颜色来提高整体感，达到最理想的视觉效果。
2, the use of close to the color of the elevator door itself of stone glue and glue stone perfect color, to fully close to the color of the original elevator door to enhance the overall sense, to achieve the best visual effects.
3、将调好的石胶进行填充，由于石胶完全凝固后会有一定程度的收缩，所以应使石胶稍微高于电梯门套水平面，这样不至于多次填充。
3, will adjust the good of stone glue fill, because of stone glue completely solidified will have a certain degree of contraction, it should be made of stone glue is slightly higher than the level of the elevator door, so as not to repeatedly fill.

4、采用打磨抛光片和打磨填充剂，使之与电梯门套成为一个水平面，增加电梯门套整体感，并解决缝隙间高低位问题，防止缝隙再次返黑。使用花岗岩翻新机配合专用剪口研磨片对剪口位进行精心打磨，使其与电梯门套成为一个平面整体。
4, the polishing and grinding filler, to become a horizontal plane and the elevator door, increase the sense of elevator door pocket integral, and solve the gap between high and low problem and prevent the gap again back to black. Using granite face lifting machine with special cutting grinding mouth piece to cut a mouth carefully burnish, make it become a whole plane and the elevator door.
5、研磨抛光：使用专用的花岗岩抛光机，从50-3000号的电梯门套水磨片由粗到细对电梯门套进行研磨，致使地面光亮平整如新。
5, grinding and polishing: use appropriative granite polishing machine from the No. 50 3000 elevator door chip mill from coarse to fine grinding of the elevator door. As a result, surface smooth and bright as new.
6、结晶处理：采用电梯门套结晶粉和结晶药剂配合晶面打磨机抛光，在打磨重压下让电梯门套和结晶粉在高温作用下发生物理和化学综合反应，形成一层致密、坚硬的结晶保护层。结晶后能增强色彩和光亮度，还能达到防滑、防水、防油等功效。
6 and crystallization processes: the elevator door crystalline powder and crystallization drug together with crystal surface grinding polishing machine, in burnish weigh for elevator door and crystalline powder physical and chemical reaction occurred under the action of high temperature, form a layer of dense, hard crystalline protection layer. After the crystallization can enhance the color and brightness, but also to achieve non slip, waterproof, anti oil and other functions.