全国服务热线:

15853163650
您当前的位置:首页 > 新闻动态 > 公司动态
    联系我们

    CONTACTS US

    地址:山东济南历城区华龙路嘉恒大厦A座1201室

    邮箱:hhjc168@126.com

    公司传真: 0531-88518398

    电话:15853163650

公司动态

COMPANY NEWS

安装仿大理石uv板有哪几种

2016-10-10 13:31:43 文章来源:www.jnhaohui.com

  仿大理石uv装饰板作为新型装饰材料,在市场上的认知度还是很高的,下面仿大理石uv板厂家给大家介绍一下:
Imitation marble UV decorative plate as a new type of decorative materials, in the market awareness is still very high, the following imitation marble UV board manufacturers to introduce you:
一、铝合金固定
Aluminum alloy fixed
1、先要在墙面上覆上一面基层,常用的是3MM的三合板,木工板,好点是防火玻镁板,用气钉把它们钉在墙面上。
1, first in the wall to cover a basic level, is commonly used in 3MM three plywood, wood board, good point is fire glass magnesium board, with gas nails they nailed on the wall.
2、再在墙面上钉脚线。用铝合金阴角固定墙角、再用铝合金工具条固定墙角。也就是分别把铝合金阴角和铝合金工具条分别用钉子钉在墙面的相应位置。
2, and then nail the foot line on the wall. With aluminum alloy corner fixed corner, and then fixed corner of aluminum alloy tools. That is, respectively, the aluminum alloy and aluminum alloy tool bar with a nail in the wall of the corresponding position.
3、再就是锯UV板。将UV板按实际要求尺寸锯成一块一块的,再将锯边用沙纸修整平整和干净。
3, and then saw UV board. The UV board according to the actual requirements of the size of sawing a piece, then sawing with sandpaper smooth and clean dressing.
4、再将UV板嵌入铝合金阴角和工具条之间就行了。
4, and then UV plate embedded in the negative angle and the tool bar between the.
二、用墙面胶安装
Two, with wall plastic installation
1、先要在墙面上覆上一面基层,常用的是3MM的三合板,木工板,好点是防火玻镁板。用气钉把它们钉在墙面上,并用沙纸将板面清洁干净。
1, the first to be covered on the wall of the grass, the commonly used 3MM three plywood, wood panels, good point is the fire glass magnesium board. Gas nail nail them on the wall, and the clean surface with sandpaper.
2、锯板,将UV板安实际要求锯成一块块的。
2, saw plate, UV plate of an actual requirement of sawn pieces.
3、倒边,将要安装的UV板四边用倒边机倒成45度角。根据实际安装要求,有的只需倒上下两边或是三个边。
3, the reverse side, will be installed on the side of the UV board with the inverted edge machine down to 45 degrees. According to the actual installation requirements, and some only need to fall on either side or three sides.
4、清洁UV板背面,用沙纸和抹布将UV板背面清洁干净。
4, clean the UV plate with sandpaper and back cloth to clean the board back UV.
5、将万能胶或木工胶均匀涂在UV板背面,然后将UV板平整地贴在墙面上,再用手轻轻捶打UV板,让UV板好好牢固粘在墙面上。
5, the adhesive or wood glue evenly coated on the UV plate on the back, and then UV plate smoothly on the wall, then gently beat the UV board, UV board to let firmly stick on the wall.
6、调水性填缝料,然后将填缝料填在两张UV板45度角相交处,先填满,再用木板垂直角从45度角相交处轻轻划过,这样45度相交处就好看了。
6, water filling material, then fill in the filler two UV in a 45 degree angle at the intersection, fill, and board vertical angle from 45 degrees angle intersection gently across 45 degrees at the intersection, so good.
7、清洁UV板表面,将多余的填缝料清洁干净。
7, clean the surface of the UV board, the excess sealant clean.
相信看了上面的介绍,您定会心动,要了解更多的仿大理石uv板内容,欢迎您进店或电话咨询更多信息,期待您的到来。
I believe that the introduction of the above, you will be moved, to learn more about the imitation marble UV board content, you are welcome to enter the shop or telephone for more information, look forward to your arrival.